Home » Didjshop Forum » Maintenance and Repair » un-polyurethane?
Re: un-polyurethane? [message #2892 is a reply to message #2891] |
Mon, 27 February 2006 07:39 |
|
JKon380
Messages: 322 Registered: November 2005 Location: USA
|
Senior Member |
|
|
I'm a big proponent of pure tung oil cut with citrus oil solvent (2:1) This is the most natural and least invasive treatment available and one that I utlize with all my termite instruments, especially yirdaki and mago. Hardening oils (tung, linseed, etc)allow the wood to breath but do this at a slower rate, so the drying-wetting cycles are not as shocking to the wood. Eucalyptus is typically very dense wood, so while absorbtion does happen, it's very minimal and only strengthens the inner bore of the instrument.
Best,
Jason
Jason
|
|
|
|
|
un-polyurethane?
By: m0lt3n on Mon, 20 February 2006 00:02
|
|
|
Re: un-polyurethane?
By: Skyer on Mon, 20 February 2006 09:12
|
|
|
Re: un-polyurethane?
By: paulb on Mon, 20 February 2006 12:36
|
|
|
Re: un-polyurethane?
By: ducpao on Mon, 20 February 2006 13:10
|
|
|
Re: un-polyurethane?
By: paulb on Mon, 20 February 2006 15:14
|
|
|
Re: un-polyurethane?
By: ducpao on Mon, 20 February 2006 23:37
|
|
|
Re: un-polyurethane?
By: m0lt3n on Wed, 22 February 2006 18:15
|
|
|
Re: un-polyurethane?
By: paulb on Wed, 22 February 2006 23:08
|
|
|
Re: un-polyurethane?
By: Skyer on Thu, 23 February 2006 02:53
|
|
|
Re: un-polyurethane?
By: paulb on Thu, 23 February 2006 09:46
|
|
|
Re: un-polyurethane?
By: m0lt3n on Thu, 23 February 2006 16:36
|
|
|
Re: un-polyurethane?
By: christos on Fri, 24 February 2006 04:09
|
|
|
Re: un-polyurethane?
By: Skyer on Fri, 24 February 2006 04:19
|
|
|
Re: un-polyurethane?
By: paulb on Fri, 24 February 2006 09:29
|
|
|
Re: un-polyurethane?
By: Skyer on Fri, 24 February 2006 09:35
|
|
|
Re: un-polyurethane?
By: JKon380 on Fri, 24 February 2006 13:56
|
|
|
Re: un-polyurethane?
By: Skyer on Sat, 25 February 2006 12:02
|
|
|
Re: un-polyurethane?
By: oddsox on Sat, 25 February 2006 14:26
|
|
|
Re: un-polyurethane?
By: Skyer on Sun, 26 February 2006 04:15
|
|
|
Re: un-polyurethane?
By: JKon380 on Sun, 26 February 2006 06:27
|
|
|
Re: un-polyurethane?
By: oddsox on Sun, 26 February 2006 08:28
|
|
|
Re: un-polyurethane?
By: Skyer on Sun, 26 February 2006 11:00
|
|
|
Re: un-polyurethane?
By: oddsox on Mon, 27 February 2006 06:23
|
|
|
Re: un-polyurethane?
By: paulb on Mon, 27 February 2006 06:43
|
|
|
Re: un-polyurethane?
By: JKon380 on Mon, 27 February 2006 07:39
|
Goto Forum:
Current Time: Sat May 18 01:36:16 CDT 2024
Total time taken to generate the page: 0.07451 seconds
|